Realistic Simcockpit
FR/EN
Reviews

Reviews / 4 November 2026

V-TRAX and AXIOM: testing a DIY motion cockpit

We tested a DIY cockpit combining V-TRAX actuators, a seat with longitudinal movement and the AXIOM belt tensioner. Rather than relying on large movements, this setup focuses on conveying road detail and combining several physical cues.

A fixed wheel, five actuators and airflow

The cockpit at Zbin’s keeps the wheel and screens stationary while the seat and pedals move. We like this approach because it preserves a consistent reference between the physical wheel and the image. A fifth actuator provides surge, moving the seat forwards and backwards during acceleration and braking.

AXIOM adds tension to the shoulder straps. Its two stepper motors produce a whistling sound that is noticeable up close. It becomes less prominent while driving, but remains an acoustic drawback. An extractor also feeds three air outlets, with airflow increasing alongside vehicle speed.

This installation remains a development platform. The actuators have different covers, and some printed parts are temporary. Its appearance therefore should not be taken as representative of a finished build.

V-TRAX: prioritising road texture

The stated aim is to reproduce small, rapid disturbances rather than move the chassis through large distances. The project combines StepperOnline motors, selected for speed, torque and low inertia, with a dedicated controller and firmware. These are design choices described during the visit, not performance figures we measured during the test.

Some actuator bodies here were previously SRT80 units, upgraded with new motors and drivers. Building from scratch is also supported through component lists and documentation. Software development continues, including work on tyre-related effects.

A budget of approximately €1,600 is mentioned during the actuator test, without a complete breakdown of what it covers. We therefore would not treat it as the price of the entire cockpit. The aim of undercutting commercial alternatives also remains a project objective rather than a verified cost comparison.

AXIOM: shoulder and waist pressure

The AXIOM housing is entirely 3D-printed. Its finish initially had us mistaking it for aluminium. The project is presented as open source, with print files, instructions and a component list. The quoted all-in build budget is around €500, with a stated force of 30 kg per strap; we did not measure that force.

The mounting arrangement for the lap straps also allows the seat’s movement to tighten the harness around the waist under braking. The resulting cue combines shoulder tension and hip pressure rather than relying solely on the tensioner’s two motors.

Control electronics and driver monitoring

The V-TRAX Box uses a circuit board and a Teensy for processing and effect generation. It can be assembled as a DIY kit or supplied built. The small solder joints require confidence, however: the mechanical assembly is not the project’s only challenge.

The configuration discussed supports six axes per box. Two boxes can be combined in SimHub for twelve axes. A Modbus connection over USB allows the plugin to monitor driver information, including power, motor temperature and torque, and send commands.

Three 48-inch screens, a homemade bezel-reduction arrangement, a GSI wheel and P2000 pedals complete the installation. We particularly liked the brake feel achieved with a customised spring combination.

Nürburgring: convincing detail, with room for tuning

From the opening laps, we could feel numerous small vibrations through the seat. The asphalt texture came through clearly without requiring large movements. Under braking, the seat moving forwards and the harness tightening worked especially well together.

Some effects would need adjustment for our preferences. Adding track geometry to surge occasionally felt excessive. Under acceleration, the seat’s very horizontal rearward movement would benefit from better coordination with the other actuators.

Configuration runs through Motion, SimHub’s paid add-on. The quality of the game’s telemetry also affects the result: capable hardware alone cannot guarantee convincing feedback.

Without the tensioner, then a single-seater at Le Mans

With AXIOM disabled, the five actuators still delivered an expressive experience. Surge quickly felt natural, even though moving the seat relative to the wheel is about creating a physical impression rather than reproducing how a real car’s cockpit moves.

We would reduce the engine-speed effect, which felt a little too prominent alongside the road information. The game’s camera movement also needed adjustment to suit the fixed wheel more closely. Meanwhile, bearings, chassis movement and vibration transmitted into the floor remained audible despite the isolation foam underneath.

The harness is therefore a useful addition rather than a requirement for enjoying the actuator system. Removing it also made it easier to focus on the motion cues themselves and distinguish them from the pressure applied by the straps.

At Le Mans, driving a single-seater at around 300 km/h produced impacts strong enough to make our voice shake, despite the limited movement amplitude. That intensity is a driving impression, not evidence that the system precisely reproduces a real single-seater.

Our assessment

### What we liked - The road detail and perceived responsiveness. - The combination of surge and harness tension under braking. - The ability to tailor individual effects.

### What we liked less - Tensioner noise and mechanical resonances. - Some overly prominent effects in the profile we tried.

We came away impressed by this DIY combination, while recognising that its success depends as much on tuning and integration as on the actuators themselves.

Join the discussion on YouTube

Related articles

Updates from the cockpit

Hardware reviews, DIY projects and updates from the channel, by email.

Julien uses your email address only for this newsletter. Unsubscribe at any time by contacting me. How your data is used